Feed aggregator

Quote: Originally Posted by mgcms1 (Post 19518) Stevo, sorry misread the control type. I'm working on a 0-P. but yes as soon as I press the insert key the same Parity High alarm pops up. No worries. I would think at this point it is going to be a hardware issue. I am not sure how to check it or what exactly to change but it looks to me like a memory board or chips that will need to be replaced.

Others with more experience on the hardware will have to chime in and help.

Stevo

There is a setting that alows handle jog without zero return.
Turn it on then you can move the head be carefull as it ignores limit switches. Only move it enough to fix the problem then turn it off.
Ray

Thanks but this machine has bad punch/Reader PCB. Anyway, I found the problem to be corrupted memory chips on the Master PCB. Replaced the chips and all is well.

Dear All,

I am Navaneethakrishnan and recently I have imported a second hand machine from USA and it is not working now.

I need your help that how to troubleshoot spindle in MDI mode.
Machine data loss due to low battery for not operating in long time.
ATC is malfunctioning and kindly advice.

Moreover can you please share machine programming manual and maintenance manual for OKK PCV 40.

I have searched in the website and I couldn't found the manual. So, kindly help me if you have.


Thanks
A. L. Navaneethakrishnan.

hi all my moriseki lathe power supply card problem.i had check that power supply fuse & capacitor damage.i change both but power supply didnt on .the error LED +5,+12,-12v led on.i had trace that pc board replace the voltage regulator ic .but that alarm not remove .after i have externally supply to the machine didnt on.there are 96 pin in power supply board which pin are enable pin .CPS 10N YASNAC. i want details on 96 pin mother board connector.thank you

Welcome to the forum...

you can get the M11 just search on the Google...

Just See, you can get all the information from the internet but at here you get the advice for your problem...

So your solution is that you have to check your machine by the experts and machine engineers...

If you want to get the perfect info of the laser machine that you purchased then you just have to send the inquiry at the needham-laser...

You just get the laser engraving machine software at the needham-laser....

Problem solved....

jdhAbfagAGgf

I posted the settings a few days ago on this thread here.

http://cnc-professional-forum.com/ma...html#post19473

Probably little use to you, but I have a dump of the parameters for a Traub TND350G using a TX8F control if you want them - may get you somewhere close

Thanks to all for your time to reply. I think I understan the G76 code now. As you can tell I'm a newbie trying to learn how to run this system. Again thanks.

Check availability or change the capacitors on the card.
they are dried up, and might be corrupted.
we had the same problem

This tool is in a turret, no tool changer, I'll try to do a compare of the PLC program to see if anything's different than what we had saved as a backup, we had thought it was more of an NC issue. I believe Deidesheim is a German company but I think this particular machine was made for a Russian company, our original electrical prints are in German and Russian.

amada laser machine is very good...
But for this you have to choose the best software and control for it...
Without this you can not set any axis of the objects that you want to do work on it...

You didn't tell anything about your problem then how can we help you...

But on way is that you can check your machine configuration at the needham-laser in UK. They definitely help you....
And one more think if you are not aware of the laser machine then you have to take advise from the Laser machine Experts...

Select the appropriate model.
select the best parts for it..

Or you can find it at the needham-laser in UK....

Nice experience...
I like your story....
Would you like to experience the another story then get the laser machine from the needham-laser. At where you get the positive response from them...

Autosizer alarm. Traced back to the amp. Changed out the amplifier. After eliminating all the I/O alarms, the unit still shows a "cut cable" on head #1.
Replaced all cables. Disconnected the cables. There is no change. This is not covered in our manuals. Any ideas out there?

Thanks

Recently purchased 3 axis Promill, with non-working M-15 Centroid control. Looking to upgrade controller, without breaking the bank! Servos and drivers appear to be good, all 3 axis will jog. I spoke to a "guru" who says he can rig a PC to my drivers, if I can come up with operating software. Anyone have any suggestions? I'm just a tired old working man, trying to set up a small shop at home, to suppliment an upcoming retirement, with limited resources. :confused: